Dirt Bike Brake Levers: 3 Tips for Maintenance and Upkeep

Dirt Bike Brake Levers: 3 Tips for Maintenance and Upkeep

Dirt bikes or off-road motorcycles are a variety of highly popular two-wheeler vehicle designed specifically to be used during off-road events and races. This type of bike is used by riders when driving on dirt paths and roads that have not been conventionally paved, as a result of which they are rugged, uneven, and bumpy. Biking on such rough and uneven surfaces can be quite difficult and often risky.

Such off-road biking can be done on naturally created dirt paths consisting of mud, sand, snow, stones, and gravel, all of which can create obstacles for the biker. Because of the difficulties posed by the rough terrain, most dirt bikes are built to be lighter and simpler than the motorcycles that are typically driven on paved roads. Moreover, dirt bikes have minimal bodywork and tough, rugged construction.

The Importance of Dirt Bike Brake Levers

For optimal performance and maximum safety, motocross racers must invest in a set of high-quality dirt bike brake levers. The performance, safety, maneuverability, and durability of the vehicle will be significantly impacted by the quality of the brake levers used. Shorter and sturdier aftermarket brake levers are more popular among dirt bike enthusiasts, as they are less likely to break off during an accident and hence last longer than other types of levers.

A set of well-made aftermarket dirt bike brake levers with a wider adjustment range will make the biking experience more comfortable, safe, and intuitive. Good dirt bike brake levers also add aesthetic appeal to the vehicle as a whole. Hence, dirt bike enthusiasts must buy the right type of brake levers, set them up properly, and maintain them conscientiously for the best riding experience in the long term.

Tips For the Installation and Maintenance of Dirt Bike Brake Levers

When installing dirt bike brake levers, motorcyclists must keep certain important factors in mind. The brake levers must be set up and maintained in a proper manner for maximum durability and performance. Well-maintained brake levers can also enhance safety as they will be unlikely to get jammed during a race or break off in case of an accident.

Certain steps need to be taken, whoever, to ensure that all the controls are in great condition and in the right place. The up and down placement of the brake levers as well as how far out they are placed can affect the maneuverability of the bike and the comfort of the rider. Good maintenance of your dirt bike brake levers will also minimize breakage, which means that you will have to spend less money on repairs and replacements over the years.

  • Proper Placement

To prevent breakage, you should move the brake levers further inwards on your handlebar. If the edge of your brake lever is a few inches behind the edge of your handlebar, then the lever will be protected even if the bike overturns during a race, with only the handlebars sustaining the impact with the ground.

The edges of the brake levers are usually flush with the ends of the handlebar on both sides. This poses a problem because when the bike overturns, the edge of the lever comes into contact with the ground along with the handlebar. And because the brake lever is more delicate than the handlebar, it often breaks off upon impact. Hence, they should always be positioned a couple of inches further in than the bike’s handlebar.

  • Perfect Elevation

How high or low the brake lever needs to be placed depends to a great extent on the preferences of the individual biker. However, as a general rule of thumb, the brake lever should not be positioned either too high or too low. Brake levers in new dirt bikes are usually positioned to be perfectly level with the handlebar.

However, ideally, the brake levers should be turned slightly downwards as that will be a more comfortable position when the rider wants to stand up on the bike while driving. This is because the angle of the wrist changes when a person is standing as opposed to sitting down on the bike. So you should position the brake levers slightly downwards until it feels comfortable when standing and when sitting down as well.

  • Extent of Tightening

Bikers should not fasten their dirt bike brake levers too tightly to the handlebar, as this makes the levers hard to move. If you tip the bike over, levers that are fastened very tightly will be more likely to break away, as extreme tightness will automatically lower flexibility and make them rigid.

The brake levers should be just tight enough so that they stay in place, while still retaining sufficient flexibility so as to be comfortable and easy to use. Hence, while you don’t want the brake levers to move around under normal circumstances, you do want them to be flexible enough so that they can move on impact with the ground without breaking off.

In Conclusion

Mentioned above are some tips to help you enhance the longevity of your dirt bike brake levers. By following these steps, you will be able to ensure your own safety and also keep your bike from getting damaged during races.

Spread Your Love & Share It.

Leave a Reply

Your email address will not be published. Required fields are marked *